#SETUP VINGCARD VISIONLINE SERIES SUPPLIES OVER#
#SETUP VINGCARD VISIONLINE HOW TO DETERMINE IF#

All access information is securely stored on the keycard. VISIONLINE OPTIONS Option 1: Visionline Offline Visionline Offline is a solution which doesnвЂ™t require any network to the locks but still offers a vast range of features. Com Vingcard 2800 User Manual.Open the catalog to page 1. Architects & specifications services. Check the system wiring.Visionline Software, Vingcard Elsafe, Ruckus, and Vostio Responsible for Mid West. Under IP Setup: - uncheck Dynamic IP address (DHCP) - set Host IP address this is the encoder IP address - set Default gateway this is the encoder gateway address - set Subnet mask this is the encoder subnet mask Figure 23 10.Under Connection Setup: - uncheck Announcement broadcast - let Server IP and Server Port be empty these parameters are not applicable for VingCard Vision - let KDE port be 3001 11.Under Misc SettingsFirst, press the back up release on the back of the bar if the door does not release the there is a fault in the systems general wiring.

Checking between red and black with a meter you should see system voltage.DOC-Live - free unlimited DOCument files search and download. Our Remote Controller is an advantageous supplement where regular locks are Third, if the door does release when you press the back up release button and you have tried adjusting the sensitivity then you need to check the voltage for the bar at the six pin connector that connects the cable to the board. Installation.The Remote Controller is fully compatible with VingCard electronic locking systems and provides access control on common doors, such as vehicle barriers, health clubs, conference suites, staff entrances, guest night entrances and more. Visionline Linear Victorian Fireplaces. : Using Vision LockLink by VingCard.

A misalignment greater than 1/8 inch end to end or front to back will cause engagement failure. There are three potential causes that can produce a failure of the buttons to seat.First, the mounting alignment between the strike and the magnet body can be off so that the buttons don't line up with the conical machined holes in the T brackets. If the buttons do not seat, the lock will not hold. Meter between the face of the bar and the point were the antenna wire solders to the board you should see near zero resistance.If everything checks out contact the factory.The SAM operates by pulling the strike plate against the magnet face when the door closes, seating the conical buttons on the strike into corresponding machined holes at either end of the magnet body.

In some cases, this problem can be corrected by adjusting the door but re-mounting the unit properly is often required.The second possible cause is that the gap between the magnet body and strike plate has widened to the point that the magnet can no longer pull the strike plate in. You should see it 'try' to move against the magnet body but note that the buttons are acting as stand-offs because they are not lining up with the holes. Watch the strike closely as you very slowly close the door.

Setup Vingcard Visionline Series Supplies Over

When this is confirmed note that the UnLatch will never operate unless the springlatch plunger is pushed in by the springlatch. If all of the LEDs are out use a meter to check between F1 and F2 on the power distribution board if you see system voltage here then your fire alarm has disconnected the system.Second, if the LED on the outside of the box is out check the AC input, if there is no AC voltage present you have found your problem.Third, if AC voltage is present check the AC input fuse.If the AC input fuse is good and you have checked everything else call the factory.On a new installation, make sure that DC power (12 or 24 volts depending on the model) is connected to the red and black wires with correct polarity. The LED should go on and the system should operate. If the LED is out disconnect the output using the associated slide switch correct the system short and then reconnect the output with slide switch. On the BPS series supplies over 1AMP each output if fused and the output LED will be on if the output is working. To correct this on the 1AMP supply, disconnect the load for 15 seconds, correct any possible system shorts and then reconnect the load.

You should be able to try operation by removing the pre-loading by pushing the door closed with enough force to counteract the pre-loading. It will operate normally when it is re-triggered. The UnLatch will automatically shut down its motor if it can't release the latch within 1.5 seconds. The UnLatch motor may not be able to release the latch under this condition, but you should be able to hear it trying to release the latch. On a service call for a unit with successful operating history, in addition to the checks mentioned above, check to see if the door and latch have gotten into a warped situation where there is heavy pre-loading on the door. To circumvent this, use a pencil or other similar object to lightly push in the springlatch plunger and then close the trigger wire to +V and you will see the UnLatch plungers move.

This re-initializes the firmware. The recovery technique is to de-power the unit, and then re-power it with the red and orange wires already connected (both then connect to +V). A crash can also occur as a random event but this is unusual. While the motor is in the process of stalling, voltage to the processor will sharply drop and this can crash the microprocessor. This can happen some times if the unit is under-powered and has consequently stalled (the motor is not receiving enough power to operate the latch). To correct this 'warped door' situation, have the door serviced and possibly increase the capacity of the power supply.If the unit still will not function, note that it does have an internal microprocessor that could have gotten into a crash condition.

If the DK-26 is receiving specified voltage, briefly short terminal SRC to terminal REX. If this restores proper voltage and operation of the DK-26, you'll have to determine if the power supply is undersized or if there is a short circuit in the lock wiring which is pulling down the power supply. Remove the lock from the circuit. If the voltage reads very low, the problem may be that a fail safe lock being controlled by the DK-26 is drawing too much current for the power supply. Call the factory.Check that power has been connected using a voltmeter on the CPU board to make sure that the correct voltage is present.

Setup Vingcard Visionline How To Determine If

If you are powering the board with DC voltage into the DC input terminals, ignore PolySwitch #1. It protects against an internal short on the board. PolySwitch #1 comes into play when you are powering the unit from an AC source connected to the AC input terminals. Each PolySwitch protects against a particular problem and you need to know how to determine if the PolySwitch has tripped and how to correct the problem and reset the PolySwitch.

Set it to DC for PolySwitches #2 and #3. If you are checking PolySwitch #1, set your voltmeter to AC. PolySwitch #3 will also trip if there are short circuit problems with the SRC, REX, UCD and HCD terminals.To check the PolySwitches, apply the probes of a voltmeter to both PolySwitch leads with the board powered. PolySwitch #3 protects against a short circuit in the keypad which can be caused by skinned keypad wires or mis-wiring the keypad cable into the CPU board terminals.

Overload current through the PolySwitch trips it so that it clamps the current down to roughly 100mA. If none of the three PolySwitches have tripped but the properly powered board will not operate its relay when SRC and REX are briefly shorted together, call the factory.If you find a tripped PolySwitch, you have reset it. A tripped PolySwitch acts as a high impedance resistor so you will read several volts across the PolySwitch leads.

It is not enough to correct the overload condition you have to depower the board for 5 seconds and the PolySwitch will reset itself.If PolySwitch #1 has tripped, visually inspect the four large diodes on the board to see if a loose wire has fallen on them to create a short circuit.

Setup Manual Vingcard Visionline